logo
Σπίτι
Προϊόντα
Περίπου εμείς
Γύρος εργοστασίων
Ποιοτικός έλεγχος
Μας ελάτε σε επαφή με
Ζητήστε ένα απόσπασμα
Ειδήσεις
TOGETHER HTL LTD
Αρχική Σελίδα Ειδήσεις

Helicoid vs Sectional Screw Flighting: Which One for Abrasive Materials?

Η TOGETHER HTL LTD είναι μια πολύ καλή εταιρεία, είμαι πολύ πρόθυμος να συνεργαστώ μαζί σας, ασφαλής, αποτελεσματική, επαγγελματική, ειλικρινής, χαρούμενη! Σας ευχαριστώ που μου παρέχετε σταθερή εξυπηρέτηση και προϊόντα. -----EUROPAT

—— EUROPT ΒΙΟΜΗΧΑΝΙΚΌ

Είμαι Online Chat Now
επιχείρηση Ειδήσεις
Helicoid vs Sectional Screw Flighting: Which One for Abrasive Materials?
τα τελευταία νέα της εταιρείας για Helicoid vs Sectional Screw Flighting: Which One for Abrasive Materials?

For abrasive materials, sectional flighting is generally the better engineering choice. The reason is physical: cold rolling draws the outer edge thinner, while sectional pressing or machining preserves full thickness at the rim. Abrasion attacks the rim first. Sectional also opens the door to Hardox, AR plate and manganese grades that continuous rolling cannot handle economically.

Why Edge Thickness Decides Wear Life

Helicoid flighting is made from strip passed through cone-shaped rolls. The outer edge is compressed during forming, so the finished helix is thick at the root and thin at the periphery—the outer edge can end up roughly half the inner-edge thickness. In light service this saves weight and cost. In abrasive service it removes the wear reserve exactly where the blade contacts the trough and the bulk material.

Sectional flights are cut from plate, split, pressed into single turns and welded into a helix. Thickness is uniform from inner edge to outer edge. A sectional flight made from 12 mm plate has 12 mm at the rim; a cold-rolled helicoid from similar strip stock does not.

Work Hardening Versus Through-Thickness Reserve

Cold rolling does harden the helicoid surface, improving resistance to moderate abrasion. That is why heavy-duty helicoid can serve limestone, cement and fertilizer reasonably well. But work hardening is a surface effect. Once abrasive wear penetrates the hardened skin, the thinner substrate offers little remaining reserve. Sectional flights can be specified in Hardox, AR plate or manganese steel, where wear resistance is a property of the plate rather than a thin surface layer—a decisive advantage in alumina, fly ash, glass cullet and mineral concentrates.

Replaceability and Downtime

A continuous helicoid is difficult to section-replace. A sectional screw can be built with bolted or segmented flights, allowing a worn 1–1.5 m section to be changed without removing the shaft or disturbing adjacent turns. In abrasive plants where downtime cost dominates the maintenance budget, this modularity often outweighs the lower purchase price of helicoid.

Selection Rule

Use sectional when abrasion is severe, thickness or diameter exceeds standard helicoid rolling limits, wear-resistant plate is required, or replaceable segments are valued. Use helicoid when abrasion is moderate, the size is standard CEMA, and first cost is the main driver.

Contact: Lucy Chai | lucychai0315@gmail.com | www.refinerdisc.com | WhatsApp: +86 15373883537

#ScrewFlight #SpiralBlade #MetalForming #HUATAO #auger #screwconveyor #feedmixer #AbrasiveWear #Hardox

Χρόνος μπαρ : 2026-11-17 17:15:15 >> κατάλογος ειδήσεων
Στοιχεία επικοινωνίας
TOGETHER HTL LTD

Υπεύθυνος Επικοινωνίας: Mr. Maple

Τηλ.:: +86 17778255675

Φαξ: 86--311-80690567

Στείλετε το ερώτημά σας απευθείας σε εμάς (0 / 3000)